Accueil

/*
ESP32 I2S Microphone Sample
esp32-i2s-mic-sample.ino
Sample sound from I2S microphone, display on Serial Plotter
Requires INMP441 I2S microphone

DroneBot Workshop 2022
  https://dronebotworkshop.com
*/

// Include I2S driver
#include <Arduino.h>
#include <driver/i2s.h>

// Connections to INMP441 I2S microphone
#define I2S_WS 25
#define I2S_SD 33
#define I2S_SCK 32

// Use I2S Processor 0
#define I2S_PORT I2S_NUM_0

// Define input buffer length
#define bufferLen 1024
int32_t sBuffer[bufferLen];

void i2s_install() {
// Set up I2S Processor configuration
const i2s_config_t i2s_config = {
.mode = (i2s_mode_t)(I2S_MODE_MASTER | I2S_MODE_RX),
.sample_rate = 40000,
.bits_per_sample = I2S_BITS_PER_SAMPLE_32BIT,
.channel_format = I2S_CHANNEL_FMT_RIGHT_LEFT,
.communication_format = I2S_COMM_FORMAT_I2S,
.intr_alloc_flags = ESP_INTR_FLAG_LEVEL1,
.dma_buf_count = 4,
.dma_buf_len = bufferLen,
.use_apll = false,
.tx_desc_auto_clear = false,
.fixed_mclk = 0
};

i2s_driver_install(I2S_PORT, &i2s_config, 0, NULL);
}

void i2s_setpin() {
// Set I2S pin configuration
const i2s_pin_config_t pin_config = {
.bck_io_num = I2S_SCK,
.ws_io_num = I2S_WS,
.data_out_num = -1,
.data_in_num = I2S_SD
};

i2s_set_pin(I2S_PORT, &pin_config);
}

void setup() {

esp_err_t RC;

// Set up Serial Monitor
  Serial.begin(115200);
  Serial.println(" ");

delay(1000);

// Set up I2S
  i2s_install();
  i2s_setpin();
  RC = i2s_start(I2S_PORT);
  if (RC != ESP_OK) {
    Serial.println("Erreur i2s_start()");
  }
  delay(500);
}

void loop() {

// False print statements to "lock range" on serial plotter display
  // Change rangelimit value to adjust "sensitivity" 
  int rangelimit = 3000;
  Serial.print(rangelimit * -1);
  Serial.print(" ");
  Serial.print(rangelimit);
  Serial.print(" ");

// Get I2S data and place in data buffer
  size_t bytesIn = 0;
  esp_err_t result = i2s_read(I2S_PORT, &sBuffer, sizeof(int32_t)*bufferLen, &bytesIn, portMAX_DELAY);

if (result == ESP_OK)
{
    /*// Read I2S data buffer
    int16_t samples_read = bytesIn / 8;
    if (samples_read > 0) {
      float mean = 0;
      for (int16_t i = 0; i < samples_read; ++i) {
        mean += (sBuffer[i]);
      }

// Average the data reading
      mean /= samples_read;

// Print to serial plotter
      Serial.println(mean);
    */
    int recu = bytesIn / sizeof(int32_t);
    for (int i=0; i<recu; i++) {
      Serial.printf("%ld\n",sBuffer[i]);
    }
    //Serial.print(" - ");
    //Serial.println(bytesIn);
  }
}